Skip to main content

LEDShoot - Electronic LED Shooting Game

LEDShoot is a simple electronic shooting game which we developed in a year end vacation period. This is a single player electronic game with following game play logic:

There are two fighting groups are exists in this game world. RED group is an enemy group and GREENs are friendly parties. Player’s job is to shoot the RED group(s) when they appear on the stage. Player gets limited time to shoot and misfires are treated as negative points. When player get 100 points game get end with winning message.


This electronic game system is mainly based on ATmega32 MCU and firmware is developed using GCC C (with Atmel Studio 6.0). This system is design to work with 5V - 1.5A power supply unit.

We developed this system as a hobby project and we construct it on a couple of breadboards, at the moment we don’t have any PCB design for this project.

When assembling the circuit make sure to use some heavy-duty push button for (SL2) control key. For (SL1) use 8Ω - 1W (60mm) speaker. LED19 indicate the "audio-mute" status of the system and player can toggle it by pressing the S2 push button.

This project is release as an open hardware project and all the source codes, schematic diagrams and compiled binaries are available to download at google drive. All the project source codes are released under the terms of GNU General Public License 3.0. Project schematic diagrams and EAGLE project files are released under the terms of Creative Commons Attribution 3.0 Unported license.

Comments

Popular posts from this blog

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle.  In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M